INTERSEAL 670HS MSDS PDF

INTERSEAL HS – PART B (REGULAR) – L () Use; Colors; MSDS / TDS; Variant; Product Review(s). Use For immersion service, Interseal HS must be applied to surfaces blast cleaned to SSPC-SP10 or Sa PT. International Paint Indonesia. Safety Data Sheet EGA INTERSEAL HS GREY PART A Version Number 2 Revision Date 06/27/ 1. Product and . International Paint Ltd. Safety Data Sheet. EGA Interseal HS Grey Part A. Version No. 2 Date Last Revised 05/10/ Conforms to the requirements of.

Author: Kazrabar Faut
Country: Mozambique
Language: English (Spanish)
Genre: Literature
Published (Last): 14 March 2008
Pages: 493
PDF File Size: 4.70 Mb
ePub File Size: 16.71 Mb
ISBN: 699-1-35962-412-4
Downloads: 79011
Price: Free* [*Free Regsitration Required]
Uploader: Nigis

Do not thin more than allowed interswal local environmental legislation. Press and move to zoom. Typical thicknesses will be between milsmicrons. Preferred application is by a suitable large tip hopper gun e.

INTERSEAL HS PLATINUM GREY MSDS Download

Mouse over image to zoom. In common with all epoxies Interseal HS will chalk and discolor on exterior exposure. With freshly blasted surfaces a slight degree of flash rusting is allowable, and is preferable to the surface being too wet. Prior to paint application all surfaces should be assessed and treated in accordance with ISO Always mix a complete unit in the proportions supplied.

Accumulated dirt and soluble salts must be removed.

Varnish Hybrid Water base. Application should then be to a suitably primed surface. Provides excellent anti-corrosive protection in industrial, coastal structures, pulp and paper plants, bridges and offshore environments in both atmospheric exposure and immersion service.

INTERSEAL 670HS – PART B (REGULAR) – 0.57L (5.63 :1)

Puddles, ponding and accumulations of interweal must be removed. Low or high temperatures may require specific application techniques to achieve maximum film build. Sagola or Air texture gun fitted with a mm nozzle. It is also possible to apply to damp surfaces in some circumstances. Level of sheen and surface finish is dependent on application method. Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner.

TOP 10 Related  LINN TONEARMS AND CARTRIDGES PDF

Dry bristle brushing will normally be adequate for accumulated dirt. Be the first to write a ijterseal for this product!

A low VOC, two component high build, high onterseal surface tolerant epoxy maintenance coating. Interseal HS can be used as a non-skid deck system by modification with addition of GMA crushed flint aggregate. However, this product is not recommended where thermoplastic coatings such as chlorinated rubbers and vinyls have previously been used.

Aged Coatings Interseal HS is suitable for overcoating a limited range of intact, tightly adherent aged coatings. A surface profile of mils microns is recommended.

However, it can be used over suitably primed surfaces. Systems iterseal Interseal HS will normally be applied to correctly prepared steel substrates. NSF Certification is for tanks greater than gallons Brush Typically mils microns can be achieved Roller Typically mils microns can be achieved How to use Mixing 670hx is supplied in two containers as a unit.

However, these phenomena are not detrimental to anti-corrosive performance.

If salt water is used in the wet blast process the resulting surface must be thoroughly washed with fresh water before application of Interseal HS. Consult International Protective Coatings for further details. Please consult International Protective Coatings for alternative recommendations. The surface to be coated should be clean, dry and free from contamination. Surface preparation The performance of this product will depend upon the degree of surface preparation.

TOP 10 Related  FUNDACION ESTEBAN TORBAR PDF

Loose or flaking coatings should be removed back to a firm edge. For application to a wide variety of substrates including hand prepared rusty steel, abrasive blast cleaned and hydroblasted steel, and a wide range of intact, aged coatings. Certification is for tanks greater than gallons Avoid using a mixture of application methods whenever possible. Warning In order to achieve optimum performance on hand prepared steel, the aluminum pigmented version should be applied as a primer coat by brush to ensure thorough wetting out of the substrate by Interseal HS.

Trowel or roller can be used for small areas.

Soluble salts should be removed by fresh water washing. Typically this would apply to C or D grade rusting in this standard.

INTERSEAL HS – PART B (REGULAR) – L ( :1)

Further information is available from International Protective Coatings. When applying by methods other than airless spray, the required film build is unlikely to be achieved. Alternatively, a broadcast method of application can be used. Once the unit has been mixed it must be used within the working pot life specified. Interseal HS is suitable for overcoating intact, aged alkyd, epoxy and polyurethane systems.

Premature exposure to ponding water will cause a color change, especially in dark colors.