BREMSHEY ORBIT PLUS MANUAL PDF

You can find the manual for your Bremshey Cross Trainer below. Bremshey Orbit Ambition Cross Trainer · Bremshey Orbit Control Cross Trainer · Bremshey. Check the reed sensor also known as the speed sensor. It is located on the front roller pulley. It is mounted to the frame and looks like a small. 18TSFC_Star Fit C HR i-Plus Crosstrainer_OMpdf . _Bremshey Orbit Ambition C_User Manual. pdf. MB.

Author: Basho Fesida
Country: Pacific Islands
Language: English (Spanish)
Genre: Video
Published (Last): 8 January 2014
Pages: 72
PDF File Size: 5.10 Mb
ePub File Size: 19.3 Mb
ISBN: 518-7-87770-546-5
Downloads: 39452
Price: Free* [*Free Regsitration Required]
Uploader: Mutaur

See section 2 Resistance settings at minimum and maximum incorrect. The software will use the calibration parameters read from the EEPROM and use them to control the electromagnetic brake without notifying anything to user.

Thereafter the console lights will flash indicating that the engineering mode has been entered. Tap the end of the drift with a hammer until the one bearing is removed.

“service manual”

The software will use the parameters from the user interface memory for controlling the electromagnetic brake but will not store them to EEPROM. Potentiometer values will show in the Time window. Introduce the belt by fitting it over the resistance flywheel boss groove side down and under the upper tension wheel kunder over the top of the floating tension wheel. The software stores the calibration parameters in two separate places: Try new Battery in HR belt 2.

TOP 10 Related  EV RE410 PDF

Physically ground the user to the machine. In such case the correct calibration parameters are on the user interface memory and should not be overwritten with the ones from the EEPROM. Defective cable or connector between the user interface and lower board a. Lower board memory is damaged and the lower board needs to be replaced Please note that the ergometer can be used normally even it gives this error during start-up.

When set re-tighten upper and lower locking bolts. Exit the engineering mode by the same key sequence as in entering. The user interface has been replaced with a new spare part. There are several screws located on the perimeter of the covers.

Insert bremxhey stone and press against copper commutator. Now lift the cable over the motor capstan e and then slide out the cable end from the capstan slot.

Bremshey Sport :: Manuals

Re-connect the btemshey supply wire to tension motor. Most treadmills will be grounded against ESD with grounding wires going from the electronics to the frame of the machine. Bremshey EMS x 2.

The lower board has been replaced with second-hand one. Remove the two securing screws on the side landing areas and manuql them off the back.

“service manual” |

If yes, may be brake mechanism problem See section 2 5. Error texts can be removed from the display p,us disconnecting the treadmill power cable for about 10 seconds.

TOP 10 Related  HARTIP 1800 PDF

To update the software proceed as follows: It assumes a certain level of technical competence and familiarity with basic hand tools. Place a long drift through the centre hole of one bearing so that it rests against the inner side of the opposite bearing.

Whilst rotating the rear drum, decrease the resistance with the meter keys to minimum checking that the cable and flywheel slider is moving freely. Before starting the update procedure make sure you have all the following: Double-click the update file and the dialog below appears 4.

Check for problems within the rear drum assembly. Screw the crank puller into the internal thread of the right side cross frame until firm. The software update file must be in the root of the flash drive i. The transmission belt if not correctly aligned tensioned can cause noise and long-term damage to the belt and other associated components. Lift motor calibration is needed if any of the following has taken place: It is a good idea to count the number of turns as this will help when the roller is retensioned.

NA Height storage position